Transcend-information 128MB-256MB JetFlash Manuale Utente

USB 128MB-256MB JetFlash™ User’s Manual P/N TS128/256MJF-WL

8personnel to assist you to complete the installation. 8. From the Start Menu, go to Settings and select Network Connections. 9. Right-click Wire

9  You can also use the KU8-M zip file in the second partition of your JetFlash. This zip file is the compressed files of the WLAN Utility. Afte

103. The IEEE 802.11b WLAN Utility (USB) window will appear.  One of following signal icons will appear in the system tray (bottom right corner) af

11 4. Select or type in the SSID you want to use (see picture below for an example). The SSID must match the one used by the Access Point.  SSI

12  Channel is not active in Infrastructure Mode.  After the values of Computer Name, SSID, Network Type, Channel and Country are set, you can t

13 Connect without an Access Point (Ad Hoc Mode) If you want to communicate with the other wireless devices directly (peer to peer) without using an

14  Every member of the peer-to-peer network must select the same SSID and channel. 5. Select Apply. 6. Select OK to activate 802.11 Ad Hoc Mode.

15 Enable Encryption You can enhance the security of network by enabling the encryption. Follow the procedures below to activate encryption. 1. Exec

16 b. If Manual 128 bits (ASCII) is selected, enter the 13-digit WEP Key(s). c. If Manual 64 bits is selected, enter the 10-digit WEP Key(s). d. If

17 4. Select Apply to finish. Setting the Transmission Rate JetFlash supports four kinds of transmission rates. You can follow the procedures bel

Table of Contents Introduction Package Contents...

18 Power Saving Mode JetFlash supports Power Saving Mode. You can follow the procedures below to enable the Power Saving Mode. 1. Execute the WLAN

19about your wireless connection. The SSID and MAC information of the network or access point to which your computer is connected will appear on the

20Diagnostic To view any errors in the hardware, firmware, or software of your JetFlash, select the Diagnostic tab in the IEEE 802.11b WLAN Utility (

21Safely Remove JetFlash Remove JetFlash in Windows 98SE Unplug JetFlash from your system directly when data is not transferring. Remove JetFlash in

22 6. The Safe To Remove Hardware window will appear again. Select OK to complete. You may now safely unplug your JetFlash from your computer. Rem

23 4. The Safe To Remove Hardware window will appear. Select OK to continue. 5. Select WLAN miniUSB Adapter and select Stop to continue. 6. The

24 Remove JetFlash in Windows XP 1. Select the icon in the system tray. 2. The Safely Remove Hardware pop-up menu will appear. Select to continue

25Uninstall WLAN Utility 1. Safely remove your JetFlash (see previous section). 2. Select the button on the Task Bar, go to Settings and then selec

26 5. Follow the InstallShield Wizard and select Remove to complete the un-installation. 6. Select Finish when the un-installation has completed.

27Troubleshooting Q1: Why doesn’t the driver CD Auto-Run after it is inserted into the CD-ROM drive in Windows? A1: This problem usually occurs bec

1Introduction Thank you very much for purchasing Transcend’s Wireless LAN JetFlash™. This small device is more than a USB Flash Drive. It combines a

28c. If an error message appears in the Device Status window, select Remove. d. Select OK to confirm the device removal. e. Select Yes to restar

29 b. Select the Device Manager tab and double-click Network adapters. Select the WLAN miniUSB Adapter and right-click Properties. c. If an error m

30 d. Select OK to confirm the device removal. e. Select Yes to restart your computer and re-insert your JetFlash.  In Windows 2000: a. Right-

31 b. Select Hardware tab and then select Device Manager. c. Double-click the Network adapters. Right-click the WLAN miniUSB Adapter and then selec

32 d. If an error message appears in the Device Status window, right-click WLAN miniUSB Adapter and then select Uninstall. e. Select OK to confirm t

33 f. Restart your computer and re-insert your JetFlash.  In Windows XP: a. Select the button on the Task Bar, go to Settings and then select C

34 c. Select Hardware tab and then select Device Manager. d. Double-click the Network adapters. Right-click WLAN miniUSB Adapter and then select Pr

35 e. If an error message appears in the Device Status window, right-click WLAN miniUSB Adapter and select Uninstall. f. Restart your computer and

36Specifications • Host Interface: USB 1.1 • Standard: IEEE802.11b • Dimension: 26 (W) x 86 (L) x 14 (H) mm • Weight: 27g • WLAN Frequency Ran

JetFlash Limited Warranty “Above and beyond” is the standard we set ourselves for customer service at Transcend. We consistently position ourselves t

2Product Overview Switch When the switch is set to the “ON” position, you can write/read data to/from your JetFlash and simultaneously use it for wi

3Data Storage Function Driver Installation for Windows 98SE 1. Drivers are required for Windows 98SE. Drivers will also be required for the WLAN fun

4 Driver Installation for Windows Me, 2000, and XP No drivers are required. These Windows operating systems have built-in drivers to support the dat

5Wireless LAN Function The WLAN Utility is JetFlash’s management software. You must install the WLAN Utility found on the Driver CD to enable the

6 4. Select Next.  You can select Browse to choose the folder destination. 5. Select Next.

7  You can rename the program folder name. 6. The Question window will appear. Select Yes to add a program shortcut on your desktop (recommended).